-
Compliance was stuck at 40%, and I was tracking the wrong number
-
The deeper reason: we were buying eyewear by unit price, not by job
-
The cost nobody puts in the procurement report
-
The decision that actually made a difference (and the mistake I almost made)
-
What I'd tell anyone buying eyewear for a team
-
The bottom line
Compliance was stuck at 40%, and I was tracking the wrong number
I've been handling PPE orders for roughly nine years now — I want to say around 2,500 purchase orders total, though I'd have to pull the system to be sure. Safety glasses alone are probably 400 of those.
For my first three years, our compliance numbers were bad. Not "needs improvement" bad. I mean buy 500 pairs, hand them out, and by the end of the quarter maybe 200 are actually on people's faces.
The rest ended up in lockers, trucks, and — one memorable time — the bottom of a toolbag that already had a half-eaten sandwich in it.
I did what everyone does. I assumed it was a discipline problem. Bought training videos. Sent reminders. Got the supervisors to do more spot checks. Compliance went from "terrible" to "somewhat less terrible."
What I actually needed to do was look at the glasses themselves.
The deeper reason: we were buying eyewear by unit price, not by job
Here's what I finally understood around 2019, and it took me embarrassingly long: we weren't buying safety glasses. We were buying a line item on a spreadsheet.
The procurement logic went like this. Safety glasses cost $2-4 per pair. We need approximately 500 per quarter. So buy the cheapest ones that meet ANSI Z87.1. End of analysis.
But that logic broke down in the field, because the cheapest compliant glasses were often the worst-performing ones. Fogged up. Scratched easily. Didn't fit well across different face shapes. Looked cheap enough that people didn't want to wear them where a supervisor or a client might see them.
And I want to be honest about something, because I think this is where a lot of procurement people quietly go wrong: a pair of glasses sitting in a locker is not "cheap." It's the most expensive option on the shelf, because you paid for it and got zero. No protection, no compliance, no goodwill with the crew.
Everything I'd read about PPE compliance said the same thing — culture, leadership buy-in, enforcement. All of that matters. But my experience with 400+ orders suggested something less convenient: most of the glasses we were buying were bad glasses. Not cheap. Bad. There's a difference.
The cost nobody puts in the procurement report
Let me put actual numbers on this, because the real cost of bad eyewear is one of those things that gets rounded to zero.
In 2021, I tracked a single quarter. We spent roughly $1,800 on 500 pairs of cheap safety glasses. (Should mention: that's just the line-item cost — not the fully loaded cost of storing, distributing, and replacing them early.) Based on the survey we ran afterward, roughly 40% of those were handed out but never really worn consistently. I'm not 100% sure the 40% number is exact, but it was close. That's about $720 effectively wasted in three months.
But that's the visible cost. The invisible cost is the incident. In February 2022, one of our warehouse staff caught a metal shard in the eye because his glasses had fogged up and he'd taken them off for "just a second" while moving a pallet. Three days out. Workers' comp claim. OSHA-adjacent paperwork that took me — I'm not exaggerating — about 11 hours to sort out.
And then there's the home-project problem. In April 2022, the same guy spent a Saturday staining a fence at home. Got a splash of stain in his eye, no glasses on, ended up in urgent care. Missed two days. The guy who couldn't tolerate our work glasses didn't instinctively reach for eye protection when he actually needed it off the clock either.
That was the moment it clicked for me. We weren't just buying bad eyewear. We were training our people to think of safety glasses as something that gets in the way, rather than something that works for them.
The decision that actually made a difference (and the mistake I almost made)
I went back and forth between two approaches for probably two months. One: keep buying cheap and enforce harder — penalties, write-ups, the whole thing. Two: spend more per pair, buy better options, and hope compliance followed.
On paper, option one made financial sense. You're not adding cost, you're just adding pressure. But my gut said it would fail — we'd already tried it, and nobody was happy, least of all the supervisors who had to do the write-ups.
I went with option two. And I made one deliberate change in how we chose the glasses: instead of buying one universal pair, we segregated by task.
For general warehouse and yard work, we went with the edge eyewear Delano G2 wraparound safety glasses — wide field of view, doesn't feel like you're looking through a porthole, and the wraparound design cut down on fogging the way a flat lens never could. For outdoor crews and anyone who spent most of their shift in the sun, we spec'd the edge eyewear Kazbek polarized safety glasses — polarized lenses, which we'd never bothered to specify before because we treated them as a "nice to have."
Both were still ANSI-compliant. Both cost more than our old baseline — maybe $6-10 per pair instead of $3-4. But by the second quarter of running the edge-eyewear line, something happened we hadn't seen before: people started asking for replacement pairs. They wanted new ones when theirs got scratched. They wanted specific models. That had literally never happened in the previous three years.
What I'd tell anyone buying eyewear for a team
I wish this were a longer list, but honestly the fix was simpler than the problem. Here's what I'd put on a sticky note.
- Buy for the job, not for the spreadsheet. A warehouse worker, a road crew in July, and a manager doing walkthroughs have different needs. Anti-fog coatings, polarized lenses, and wraparound designs aren't upsells — they're specifications. Equally: if you're already buying a hard hat and nitrile gloves for the same crew, your eyewear needs to work with both. We had guys who wouldn't wear glasses because they pinched under their hard hat strap. Lower-profile frames solved it. Small detail, big compliance number impact.
- Factor in the replacement rate. Cheaper glasses scratch faster and get replaced more often. My rough estimate from the 2021-2022 data was that the more expensive-looking option actually cost us about 8% less over the year. Probably more, if you count my time on that incident paperwork.
- Don't oversell the protection. This one I learned from an FTC compliance webinar in mid-2023, no joke. Per FTC guidelines, any safety claim about a product has to be truthful and substantiated with evidence. We had a vendor rep try to tell us his glasses offered "100% impact protection." We asked for the test data. There wasn't any. We didn't buy them.
The bottom line
I spent three years thinking our safety glasses problem was a people problem. It was actually a purchasing problem, a fit problem, and — the part that took longest to see — a framing problem. We'd taught our team, without meaning to, that safety glasses were something to be tolerated instead of something that works for them.
Once the glasses were actually comfortable, actually fit the job, and actually looked like something a person would choose to wear, compliance stopped being a battle. It just became the default.
That's not a dramatic story. But it's the one I wish someone had told me in 2017, before I spent four figures learning it the hard way.